www.iFourWinns.com

Dedicated to Current and Future Owners
It is currently Thu Oct 31, 2024 6:46 pm

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
PostPosted: Tue Dec 01, 2015 12:54 am 
Offline
Seahorse

Joined: Fri Jun 19, 2015 9:48 pm
Posts: 28
Location: Washington, PA
I winterized my H210 last weekend and in the process tried to change the drive oil. I couldn't get the bottom drain plug out on the outdrive. Any suggestions? I didn't pry on it too hard so as not to tear up the slot in the plug for the flat screwdriver. Thanks in advance!

It was a pretty good boating season, in my opinion, when I can take the boat out around Thanksgiving in Southwestern PA!

_________________
2010 Four Winns H210 - 5.0 Mercruiser
Image


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 1:10 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Are you using the largest flat blade screwdriver that physically fits in the slot?
If so, get a hammer and give it a couple of soft impacts to break the seizure.

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 1:36 am 
Offline
Seahorse

Joined: Fri Jun 19, 2015 9:48 pm
Posts: 28
Location: Washington, PA
Yes, largest flat screwdriver - it fits well in the slot. I'll try tapping again with a hammer. I might stop at Harbor Frieght to see if they have a torque multiplier that may work.......

_________________
2010 Four Winns H210 - 5.0 Mercruiser
Image


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 5:03 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Cordless Impact Drivers (Makita/ Bosch etc) will make light work of jobs like these. 8)

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 8:43 am 
Offline
email admin your custom rank

Joined: Sun May 20, 2012 4:31 pm
Posts: 875
Location: Minneapolis, MN
I have used something similar to this
http://www.harborfreight.com/impact-scr ... 37530.html
Get a screwdriver tip that fits well. Apply some force to loosen the screw while holding the tool, and give it a tap with a hammer. Sometimes a tiny bit of valve grinding compound on the screwdriver blade will help keep the screwdriver from slipping. Good Luck.

_________________
Surface Interval: A scuba diving term for that time between dives to relax and prepare for life's next great adventure.

Current boat: '02 FW 268 Vista
Previous boat: '95 FW 190 Horizon


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 4:38 pm 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
I don't know if they are available for Merc drives but the drain plugs that BRP now sells for Evinrudes and the Cobra drives have an allen recess in them instead of a screw slot. Much easier to remove. I have been using them for the past 5 years or so....

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 5:30 pm 
Offline
email admin your custom rank

Joined: Sun Jul 22, 2012 5:10 pm
Posts: 2032
Location: West Palm Beach, FL
Surface Interval wrote:
I have used something similar to this
http://www.harborfreight.com/impact-scr ... 37530.html
Get a screwdriver tip that fits well. Apply some force to loosen the screw while holding the tool, and give it a tap with a hammer. Sometimes a tiny bit of valve grinding compound on the screwdriver blade will help keep the screwdriver from slipping. Good Luck.

+1
These are great tools because the impart the torque at the same time as the impact, so the bit cannot try to climb out of the slot (and the impact also helps break the seize as Lou mentioned). I haven't tried the Harbor Freight version though.

_________________
Image
"Knot Easy" 2000 Horizon 240 Volvo 5.7GS /SX
tow: 2017 Honda PILOT EXL-AWD
prev. boats:
'87 Chaparral 198CXL 4.3 OMC Cobra
'69 Jetstar 16ft Ski Boat, 115hp Yamaha
'68 Aluminum Jon Boat, 3hp Sears
'64 Water Wings


Top
 Profile  
 
PostPosted: Tue Dec 01, 2015 8:11 pm 
Offline
Shark

Joined: Tue May 06, 2014 7:25 am
Posts: 145
Location: Ohio
I had the same issue getting my drain plug out of my Cobra and best thing to get is what they call a drag link socket. Basically large screwdriver tip on a 3/8 or 1/2 socket drive. Tip was little larger then the screwdriver slot but 3 seconds on the bench grinder fixed that.

http://www.mscdirect.com/browse/tn/Hand ... 4287584684

_________________
2008 H200 Frenzy Edition 5.0 GXi

1993 Horizon 190 5.0 EFI (Sold)


Top
 Profile  
 
PostPosted: Wed Dec 02, 2015 4:08 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
LouC wrote:
I don't know if they are available for Merc drives but the drain plugs that BRP now sells for Evinrudes and the Cobra drives have an allen recess in them instead of a screw slot. Much easier to remove. I have been using them for the past 5 years or so....


Hey Lou,

I've had a brief look and can't find a part number for these...
Might you know one for the SX Cobra?

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
PostPosted: Wed Dec 02, 2015 7:57 pm 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
Don't know if they ever made them for the Volvo SX model. I know that BRP changed the newer Evinrudes to this style drain plugs and because the thread was the same on the older and newer Evinrude lower units as the Cobra, they fit Cobras too. Nice thing is that they just come out, no worry about the slot wallowing out. If they are not available OE its possible that Sierra might make an aftermarket set....

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
PostPosted: Fri Dec 04, 2015 12:59 am 
Offline
email admin your custom rank

Joined: Thu May 27, 2010 9:10 am
Posts: 1488
On my old boat, I had the merc and also had issue with drive drain plug. I went the cheap brought and threw the vice grips on large screwdriver. Used one hand to force pressure on driver and other to crank on vice grips.

_________________
http://i1339.photobucket.com/albums/o71 ... wqm355.jpg


08' H210SS
VP 5.7Gi


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group