| www.iFourWinns.com https://www.smwebhead.com/phpBB3/ |
|
| OEM table location https://www.smwebhead.com/phpBB3/viewtopic.php?f=3&t=12403 |
Page 1 of 1 |
| Author: | Linecapt [ Sun Oct 06, 2013 8:00 pm ] |
| Post subject: | OEM table location |
Hi folks, as a new to me owner of a '05 H210, the wife would like to add the table. My question is, those of you with an original, factory mounted table, where is it located and might you have any pics of it installed? Thanks in advance. |
|
| Author: | schoolsOut [ Sun Oct 06, 2013 8:19 pm ] |
| Post subject: | Re: OEM table location |
Congrats on your 210. We love ours and I'm sure you will too. The table mounts into the floor in the u-seat. We rotate the cockpit seats around to use at the table too. Here are two pics. One shows the table in use, the other shows the location in the floor of the black mount cap.  
|
|
| Author: | Linecapt [ Fri Dec 06, 2013 7:06 am ] |
| Post subject: | Re: OEM table location |
Ok, great, thanks for the pics. Helps a bit. But also in that vicinity, I have an inspection cover for the fuel tank. Is your mount mounted over the same cover plate? |
|
| Author: | pet575 [ Fri Dec 06, 2013 10:07 am ] |
| Post subject: | Re: OEM table location |
Mine similar location but mounted into the base of the u-seat. The pole that the table sits on has a 45 degree bend in it. Don't have any pics sorry. |
|
| Author: | schoolsOut [ Fri Dec 06, 2013 9:00 pm ] |
| Post subject: | Re: OEM table location |
Linecapt wrote: Ok, great, thanks for the pics. Helps a bit. But also in that vicinity, I have an inspection cover for the fuel tank. Is your mount mounted over the same cover plate? I also have the access cover for the fuel tank, but I think mine is closer to the ski locker. The table mount is between the fuel tank access and the aft seat. Boat is in storage so I don't remember the exact location of the access cover, but I'm pretty sure that is how it is. |
|
| Author: | Linecapt [ Thu Mar 27, 2014 8:06 pm ] |
| Post subject: | Re: OEM table location |
Pet575, I just bought one of the side mount angled pedestal tables, in transit to me. I went with the cheaper anodized aluminum instead of stainless steel. What is yours made of, and how sturdy is it? |
|
| Author: | schoolsOut [ Thu Mar 27, 2014 8:41 pm ] |
| Post subject: | Re: OEM table location |
Where did you purchase your table? |
|
| Author: | Cap'n Morgan [ Fri Mar 28, 2014 8:19 am ] |
| Post subject: | Re: OEM table location |
http://www.iboats.com/Acrylic-Coated-Ov ... _id.713781 We bought our's 2 years ago. Beats the hell out of a hole in your floor, the side mount is very sturdy as well. |
|
| Author: | pet575 [ Fri Mar 28, 2014 11:27 am ] |
| Post subject: | Re: OEM table location |
Linecapt wrote: Pet575, I just bought one of the side mount angled pedestal tables, in transit to me. I went with the cheaper anodized aluminum instead of stainless steel. What is yours made of, and how sturdy is it? Mine stainless. Is incredibly sturdy and solid. I would not be afraid to use it for holding probably 15 lbs. |
|
| Author: | Linecapt [ Sat Mar 29, 2014 6:48 pm ] |
| Post subject: | Re: OEM table location |
Thanks for all the help and advice everyone. I did finally pull the trigger and get a side mount, anodized aluminum pedestal table mount, from Wholesalemarine.com. They were the cheapest out there for the product and shipping. Look forward to mounting it and using it, as April is around the corner and by the end of the month, boat will be in the water. Everyone enjoy and be safe. |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|