Sorry, I wish I could! I don't have an H190.
Hopefully the bump to the top will get you some more attention.
| www.iFourWinns.com https://www.smwebhead.com/phpBB3/ |
|
| ATTENTION, i need help https://www.smwebhead.com/phpBB3/viewtopic.php?f=3&t=14536 |
Page 1 of 1 |
| Author: | Jdpber [ Thu Oct 22, 2015 8:00 pm ] |
| Post subject: | ATTENTION, i need help |
Ok I have asked a couple people and no one has remembered to measure for me. I need the measurements on a captain seats layout Horizon 190. I need the locating measurements for both sides gummed to the base and dash wall to base. Please someone help me asap. I am needing to layout tape lines for the none skid and I need to not have none skid under the bases. Please someone asap thanks guys |
|
| Author: | Jdpber [ Mon Oct 26, 2015 8:28 am ] |
| Post subject: | Re: ATTENTION, i need help |
someone please |
|
| Author: | purdueosch [ Mon Oct 26, 2015 2:10 pm ] |
| Post subject: | Re: ATTENTION, i need help |
Sorry, I wish I could! I don't have an H190. Hopefully the bump to the top will get you some more attention. |
|
| Author: | zims1993 [ Mon Oct 26, 2015 7:07 pm ] |
| Post subject: | Re: ATTENTION, i need help |
I can get you the captains chair only. You just want from dash panel to the seat base and side to seat base correct? |
|
| Author: | FASTBULLITT [ Mon Oct 26, 2015 9:27 pm ] |
| Post subject: | Re: ATTENTION, i need help |
I have 96 190 in the middle of restoring with the floor out already not sure if it the same |
|
| Author: | Jdpber [ Wed Oct 28, 2015 10:15 am ] |
| Post subject: | Re: ATTENTION, i need help |
zims1993 wrote: I can get you the captains chair only. You just want from dash panel to the seat base and side to seat base correct? YES. this will locate the under floor backing support that is key for the base bolts to tap into.. thanks If you can get me the measures to the edge of the base circle and to the center point of the post that would be GOLD! |
|
| Author: | rpengr [ Wed Oct 28, 2015 1:18 pm ] |
| Post subject: | Re: ATTENTION, i need help |
Jdpber, I would take this as an opportunity to put the seat where it fits you best. Left-to-Right: The seat should be straight back from the centerline of the steering wheel, or maybe up to 1/2" inboard or outboard from there. (inboard for easier seat swiveling, or outboard for more walking room). Front-to-Back: I like to be able to stand and drive. With the steering wheel mounted, I would try the seat in a position that works with both seated and standing driving positions. Most boats come with the seat to far forward for my taste (because this makes the boat look roomier in the showroom). Ray |
|
| Author: | Jdpber [ Thu Oct 29, 2015 3:41 pm ] |
| Post subject: | Re: ATTENTION, i need help |
rpengr wrote: Jdpber, I would take this as an opportunity to put the seat where it fits you best. Left-to-Right: The seat should be straight back from the centerline of the steering wheel, or maybe up to 1/2" inboard or outboard from there. (inboard for easier seat swiveling, or outboard for more walking room). Front-to-Back: I like to be able to stand and drive. With the steering wheel mounted, I would try the seat in a position that works with both seated and standing driving positions. Most boats come with the seat to far forward for my taste (because this makes the boat look roomier in the showroom). Ray their are already backer blocks for the base bolts under the floor i have put in place. in the factory location as i was happy. the floor is glassed in and i have accidentally faired over the sharpe marks. |
|
| Author: | zims1993 [ Thu Oct 29, 2015 4:02 pm ] |
| Post subject: | Re: ATTENTION, i need help |
I'll swing by my storage unit Friday or Saturday and get the measurements for you. |
|
| Author: | Jdpber [ Thu Oct 29, 2015 9:30 pm ] |
| Post subject: | Re: ATTENTION, i need help |
zims1993 wrote: I'll swing by my storage unit Friday or Saturday and get the measurements for you. Thanks a million |
|
| Author: | TX H210SS [ Thu Oct 29, 2015 11:34 pm ] |
| Post subject: | Re: ATTENTION, i need help |
I would help but my boat is wrong model. If the block has the metal nut inserts to screw bolts into, you may consider using magnet on a string or magnetic stud finder. |
|
| Author: | zims1993 [ Tue Nov 03, 2015 6:58 pm ] |
| Post subject: | Re: ATTENTION, i need help |
Ok got these measuremets yesterday. I have 33-1/2 from the front wall to the tip of the base circle on the front and 14-1/2 to the side. |
|
| Author: | Jdpber [ Thu Nov 05, 2015 2:46 pm ] |
| Post subject: | Re: ATTENTION, i need help |
zims1993 wrote: Ok got these measuremets yesterday. I have 33-1/2 from the front wall to the tip of the base circle on the front and 14-1/2 to the side. grassy ass |
|
| Author: | purdueosch [ Thu Nov 05, 2015 5:04 pm ] |
| Post subject: | Re: ATTENTION, i need help |
Jdpber wrote: zims1993 wrote: Ok got these measuremets yesterday. I have 33-1/2 from the front wall to the tip of the base circle on the front and 14-1/2 to the side. grassy ass ^^ LOL  ^^"gracias" |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|