www.iFourWinns.com

Dedicated to Current and Future Owners
It is currently Mon Apr 29, 2024 6:49 am

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Out drive seal questions
PostPosted: Mon Jun 27, 2016 6:27 am 
Offline
email admin your custom rank
User avatar

Joined: Mon Jun 21, 2010 7:58 am
Posts: 189
Location: Central East Coast Florida
I just pressure tested my outdrive. I set it at 15 psi. It slowly dropped to 10 psi in an hour but then held 10 psi overnight. Is this good or should I look at replacing seals. ????
Thanks Rob

_________________
Anything Worth Doing Is Worth Overdoing :)
2001 Horizon 180
ImageImage


Top
 Profile  
 
PostPosted: Mon Jun 27, 2016 1:09 pm 
Offline
email admin your custom rank

Joined: Sun Jul 22, 2012 5:10 pm
Posts: 2032
Location: West Palm Beach, FL
Sounds like it worked some crud out if a seal. If you are a trailer boater, I would not be concerned at all.

If you are about to put it on a mooring or dock for a season, I would consider running it some, then testing again. Still, if it held at 10psi all night it does not sound like you have any issue.

_________________
Image
"Knot Easy" 2000 Horizon 240 Volvo 5.7GS /SX
tow: 2017 Honda PILOT EXL-AWD
prev. boats:
'87 Chaparral 198CXL 4.3 OMC Cobra
'69 Jetstar 16ft Ski Boat, 115hp Yamaha
'68 Aluminum Jon Boat, 3hp Sears
'64 Water Wings


Top
 Profile  
 
PostPosted: Mon Jun 27, 2016 11:49 pm 
Offline
230 Mike
User avatar

Joined: Mon May 15, 2006 7:59 pm
Posts: 5141
Location: Kansas City, Table Rock Lake
Which drive? I have the factory test procedure if you want it for a Volvo.

_________________
Image

Mike
2005 Four Winns 230/240
VP 5.7GXi/DP
1998 F-150 XLT
Boat Pic


Top
 Profile  
 
PostPosted: Mon Jul 25, 2016 2:50 pm 
Offline
email admin your custom rank
User avatar

Joined: Mon Jun 21, 2010 7:58 am
Posts: 189
Location: Central East Coast Florida
I just wanted to give an update on my outdrive seal. Volvo Penta SX on a 2003 Horizon 180 with 5.0 GL engine.
Last July when I took the boat out of the water I noticed foamy outdrive oil. I refilled with new oil and stored the boat for the winter. Prior to putting the boat in late June I emptied the oil and ran a pressure test on the outdrive. It would not hold 15 psi but held 10 psi overnight. So I took a chance and replaced all 3 of the o-rings in the fill and drain and level check plugs. When I pulled the boat out after a month in the water the oil was clear and clean. Looks like I just had a bad o-ring.
Rob

_________________
Anything Worth Doing Is Worth Overdoing :)
2001 Horizon 180
ImageImage


Top
 Profile  
 
PostPosted: Tue Jul 26, 2016 8:36 am 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5662
Location: Long Island NY
I'm not sure what their spec is for the pressure it should hold but I always replace the fiber sealing washers on my Cobra and have not had milky gear oil for many years.

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 63 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group