| www.iFourWinns.com https://www.smwebhead.com/phpBB3/ |
|
| Tabs https://www.smwebhead.com/phpBB3/viewtopic.php?f=3&t=9026 |
Page 1 of 1 |
| Author: | Kelleyo [ Wed Apr 04, 2012 8:29 pm ] |
| Post subject: | Tabs |
So my marina tells me it will take an entire day ($600 labor) to install some bennett hydraulic tabs on my 240. Really? |
|
| Author: | jsimon [ Wed Apr 04, 2012 9:23 pm ] |
| Post subject: | Re: Tabs |
Don't be mad... But it sounds reasonable to me. 1 mount tabs. 1 hr each each 2 mount pump 1 hour 3 run hyd lines 1 hour 4 run power to pump 1 hour 5 mount switch 1 hour 6 run switch wires 1.5 - 2 hours 7 fill resivoir and bleed .75 8 test and check for leaks .5 9 clean up mess 1 hour There is 10 hours with no warranty built in. And I'm probably low on my numbers. You can always do something quicker in your mind than in reality. |
|
| Author: | Paul I. [ Wed Apr 04, 2012 10:05 pm ] |
| Post subject: | Re: Tabs |
Kelleyo wrote: So my marina tells me it will take an entire day ($600 labor) to install some bennett hydraulic tabs on my 240. Really? I have alway done them my self. It took me all day, but I was not pushing myself. |
|
| Author: | ric [ Wed Apr 04, 2012 10:46 pm ] |
| Post subject: | Re: Tabs |
Sounds about right price wise. |
|
| Author: | Flying Sushi [ Thu Apr 05, 2012 6:02 am ] |
| Post subject: | Re: Tabs |
Since Four Winns did not offer an option of Trim Tab for our old 2006 Horizon 240 so I installed them myself... It took me 5 hours to install with wiring to dash. However, took about a three weeks to research and get right tabs for 240 (newer generation).... Ended up with same size as Option for 260 which is not as large as I wanted but based on limited area available to install tab for our boat we do not have too much choice..... Still worked great and I would recommend for anyone. |
|
| Author: | Kelleyo [ Thu Apr 05, 2012 12:17 pm ] |
| Post subject: | Re: Tabs |
Thanks. I am towing my boat to Gainesville Marina tomorrow to have an extended swim platform installed. They are also going to change oil and impeller and any other recommended services. While she is there I was think about putting on the tabs. THere is a cutout ont he dash for the tabs. Can anyone confirm if the wiring is already in place from the factory? |
|
| Author: | Flying Sushi [ Thu Apr 05, 2012 4:57 pm ] |
| Post subject: | Re: Tabs |
Wiring harness of 230/240 is same as 250/260 and even FW did not offer trim tab as an option for 230/240 the harness came with prep for Bennett Trim Tab and pumps... I had no problem with finding the plugs on 2006 Horizon 240 harness so assuming earlier model should be the same... It shows on the wiring schematics... 2003 is a year they call 240 where other years are 230....... manual says 230 as you already know. http://www.fourwinns.com/past_product/o ... Wiring.pdf |
|
| Author: | Kelleyo [ Sun Apr 08, 2012 7:51 am ] |
| Post subject: | Re: Tabs |
So I dropped her off at Gainesville Marina. That is the furthest I have ever towed it with my Pathfinder. Here is what is being done: FW factory Extended swim platform Bennet Trim Tabs mounted like DaleG Teleflex Xtreme shift cable Change oil Impeller check tune (plugs, etc) Lube lower leg |
|
| Author: | 230 Mike [ Sun Apr 08, 2012 12:17 pm ] |
| Post subject: | Re: Tabs |
She'll seem like a different boat after all that! Good luck. |
|
| Author: | Rick8016 [ Mon Apr 09, 2012 7:05 pm ] |
| Post subject: | Re: Tabs |
I just had them put on my 250 and that's about what I paid. |
|
| Author: | Jafo4U [ Tue Apr 10, 2012 8:55 am ] |
| Post subject: | Re: Tabs |
Don't have tabs on my 220 not sure she needs them either. I don't tube much or pull anyone just like to cruise and hear some music and hit the sandbar. |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|