| www.iFourWinns.com https://www.smwebhead.com/phpBB3/ |
|
| New Gage cluster? https://www.smwebhead.com/phpBB3/viewtopic.php?f=5&t=12720 |
Page 1 of 1 |
| Author: | hail mary [ Sun Mar 23, 2014 11:04 am ] |
| Post subject: | New Gage cluster? |
Hi guys Update ...my tach was reading 1400rpms higher on wot , my mechanic says i would need to replace the whole cluster? Anyone had to do this or where to get one ...how much?, thx |
|
| Author: | NiagaraChillin [ Sun Mar 23, 2014 12:31 pm ] |
| Post subject: | Re: New Gage cluster? |
Unfortunately, your mechanic is right on this one. The VDO clusters are notorious for bad/wrong/false/no readings. All has to do with a factory grounding issue, which can be found in several threads here. If I was you, I would buy an aftermarket tach, and put it on/near dashpad. They are simple to hook up, do not cost much, and are 1000% more reliable than the factory VDO cluster. To replace the VDO with another VDO would be throwing money away. Of course you could always upgrade to a new Faria style panel. Several folks have done that here, it can be on the expensive side, and most guys end up making their own custom panel. |
|
| Author: | Graham R [ Sun Mar 23, 2014 5:35 pm ] |
| Post subject: | Re: New Gage cluster? |
Check it's not slipped into the V6 cylinder setting; e.g. a tach set for a 6 cylinder engine showing 6400 (1400 above say 5000 rpm) would equate with 4800 rpm for a V8. I think I got that right !! |
|
| Author: | Joe [ Sun Mar 23, 2014 6:17 pm ] |
| Post subject: | Re: New Gage cluster? |
Yeah, this is pretty typical. I purchased my own gauges and fabricated my own cluster out of carbon fiber. |
|
| Author: | hail mary [ Sun Mar 23, 2014 6:26 pm ] |
| Post subject: | Re: New Gage cluster? |
how much is a faira replacement cluster? Where do you get one , Also the tach should be a easy hookup to install one exterior of the dash?, thx |
|
| Author: | NiagaraChillin [ Sun Mar 23, 2014 6:34 pm ] |
| Post subject: | Re: New Gage cluster? |
Graham R wrote: Check it's not slipped into the V6 cylinder setting; e.g. a tach set for a 6 cylinder engine showing 6400 (1400 above say 5000 rpm) would equate with 4800 rpm for a V8. I think I got that right !! Ohh yeah, that has been known to happen. Setting for V6/V8 is on the back of the cluster I think, up under the dash. Or do you have to remove tach from cluster? can't remember. hail mary wrote: how much is a faira replacement cluster? Where do you get one , Also the tach should be a easy hookup to install one exterior of the dash?, thx Well, the prob is, they don't make a direct swap Faria cluster for our year FW's. Most guys here buy the individual gauges, cut a dash panel from wood, aluminum, or carbon fiber, then put it in the dash. And yes, if ya buy a tach, follow directions that come with it as far as which wires connect to what, then pick a spot you want to put it. |
|
| Author: | hail mary [ Wed Mar 26, 2014 9:11 am ] |
| Post subject: | Re: New Gage cluster? |
Ok I will get a new tach and install , thanks again |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|