www.iFourWinns.com
https://www.smwebhead.com/phpBB3/

Another parts request
https://www.smwebhead.com/phpBB3/viewtopic.php?f=5&t=13252		 Page 1 of 1
Author:  204Angler [ Thu Jul 24, 2014 10:32 am ]
Post subject:  Another parts request
The bow anchor locker hatch, I have the latch but it is broken and won't, well---latch. I know this will be an issue while cruising it will fly open and slam against the bow, especially going through the chop. Anybody have one that they are willing to part with or know of a website? I've searched a little but figure this was the best place to ask
Author:  kd4pbs [ Thu Jul 24, 2014 11:01 am ]
Post subject:  Re: Another parts request
You'll be on Harris or Jordan? This will work fine. ;)
Image
Author:  ric [ Thu Jul 24, 2014 11:08 am ]
Post subject:  Re: Another parts request
Post picture of said latch. Should be easy to find a replacement
Author:  NiagaraChillin [ Thu Jul 24, 2014 11:31 am ]
Post subject:  Re: Another parts request
Try this site, lots of cool stainless stuff: http://www.marinepartdepot.com/dring.html
Author:  john55c [ Thu Jul 24, 2014 11:56 am ]
Post subject:  Re: Another parts request
Mine does that too. I used vinyl foam tape and lined the two sides of the "V" of the locker, and it makes a snug fit for the locker and props it up enough that the latch is under a slight amount of upward pressure and stays in place.
Author:  204Angler [ Fri Jul 25, 2014 6:05 am ]
Post subject:  Re: Another parts request
kd4pbs wrote:
You'll be on Harris or Jordan? This will work fine. ;)
Image


Yeah, no doubt. I'd need duct tape, making the letters that form the word, "bayliner", too
Author:  204Angler [ Fri Jul 25, 2014 6:07 am ]
Post subject:  Re: Another parts request
ric wrote:
Post picture of said latch. Should be easy to find a replacement


Ok will do. I'll get a picture of it today when I get home from work and post it up. I've not seen a latch like this on other makes, so I am fairly certain it is FourWinns specific. I'm not sure though, you guys might have to tell me that!
Author:  204Angler [ Fri Jul 25, 2014 6:48 am ]
Post subject:  Re: Another parts request
NiagaraChillin wrote:
Try this site, lots of cool stainless stuff: http://www.marinepartdepot.com/dring.html


That's an awesome website. I didn't see that particular hatch in there, not saying nothing else will work though. This will be a good website to reference when replacing all deck hardware come winter. Thanks Niagara!

john55c wrote:
Mine does that too. I used vinyl foam tape and lined the two sides of the "V" of the locker, and it makes a snug fit for the locker and props it up enough that the latch is under a slight amount of upward pressure and stays in place.


That stuff that is adhesive on one side? That is a great idea for the meantime...I just don't want that hatch slamming up and down, especially after I do a high speed buff and polish and get the gel looking sharp!
Author:  john55c [ Fri Jul 25, 2014 7:41 am ]
Post subject:  Re: Another parts request
john55c wrote:
Mine does that too. I used vinyl foam tape and lined the two sides of the "V" of the locker, and it makes a snug fit for the locker and props it up enough that the latch is under a slight amount of upward pressure and stays in place.


That stuff that is adhesive on one side? That is a great idea for the meantime...I just don't want that hatch slamming up and down, especially after I do a high speed buff and polish and get the gel looking sharp![/quote]
Yes, something like this. http://solutions.3m.com/wps/portal/3M/en_US/Adhesives/Tapes/Products/~/3M-Vinyl-Foam-Tape-4714?N=3294263220+5927712&rt=rud I put it on last season and it is still doing the trick. I will need to replace it after this season, but its a cheap fix and works well and no one will see it.
Author:  rpengr [ Fri Jul 25, 2014 8:47 am ]
Post subject:  Re: Another parts request
The latch is made by Southco: http://www.southco.com
Author:  204Angler [ Fri Jul 25, 2014 11:55 pm ]
Post subject:  Re: Another parts request
rpengr wrote:
The latch is made by Southco: http://www.southco.com


Awesome, thank you so much for that website! Ill look around and find it on the site. There is a lot of good looking stuff!

Now I just need to locate those two vent windows that everyone else seems to need for their 195's

Thanks again sir
Author:  204Angler [ Sat Jul 26, 2014 8:54 pm ]
Post subject:  Re: Another parts request
Sorry haven't got a picture of that hatch latch yet. Had to drop the lower unit on my other boat to adjust shift rod
Page 1 of 1 All times are UTC - 6 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/