www.iFourWinns.com
https://www.smwebhead.com/phpBB3/

General part questions and pedestal table mount for 2005 328
https://www.smwebhead.com/phpBB3/viewtopic.php?f=6&t=11792		 Page 1 of 1
Author:  annapolis [ Fri Jun 14, 2013 11:41 am ]
Post subject:  General part questions and pedestal table mount for 2005 328
When I call my local previous Four Winns dealer he has been unable to get me parts I need the last 4 out of 4 times. He is no longer a dealer but can get parts from FW if they are carrying them.
He explained everything was a crap shoot these days.

Can anyone suggest a Four Winns dealer that would have sold bigger Vistas who might have a good supply of parts on hand?

Specifically right now I need the table mount assembly for the table over the engine compartment. I need both the round piece that bolts down to the engine cover and the pole itself.

Several I have found of other brands do not match where the bolts are and the table pole is too long.

Yes I can make it work if I want to drill new holes etc but I prefer to try to find it and install it in 10 minutes given all the other things I am working on.

BTW- my pole got so stuck in the piece on the floor that it would not come out. We tried to take it out buy removing everything and and then hitting it with two rubber hammers but it broke one side of the mount off.

Eric
2005 328 Vista

Regards,
Eric
Author:  afw200 [ Fri Jun 14, 2013 11:59 am ]
Post subject:  Re: General part questions and pedestal table mount for 2005
Too late, but table legs that are stuck, can be removed by moving them from side to side. That will loosen the leg enough to remove it from the base. Attempting to pull, or force it straight out will not work, as you now know.

As far as OEM parts go, have you tried to look up the part #'s for the leg and base on the Four Winns website parts catalog?
Author:  annapolis [ Fri Jun 14, 2013 12:13 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
I will try to website...

We tried a lot of moves before we tried the hammers. It had been like that for a few years..
Author:  wkearney99 [ Fri Jun 14, 2013 12:16 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
FWIW, I find it useful to dab a smear of anti-seize on the fittings to help prevent them from corroding in place like that. Otherwise some penetrating oil (not WD40... just let's not go there) into the joint should eventually help it work loose. Which doesn't help when you want to remove and store them NOW.

I don't know what's used on the 328, but the legs and sockets on our 348 were made by Garelick. These are the aluminum ones, extruded with a fluted profile around them.

As for the pole length, if you find something close then you might consider having a local muffler shop put the squeeze on the ends if it. Just a slight bit to aid inserting it into the socket.

Other that clearly welded bits like the stair and bow rails, there's not a lot of custom-made metal stuff on the boats. The trick is figuring out which vendor supplied them to FW. I've found they'll usually tell you if you ask.
Author:  erie cruiser [ Fri Jun 14, 2013 12:51 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
I order FW parts from a dealer in Pittsburg Pa, he will ship them directly to your home, his number is 412-896-6475 (Bill). It does help to have the FW part number handy if you speek to him. Good luck.
Author:  psusound [ Fri Jun 14, 2013 2:43 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
I would find the part numbers on four winns Part Finder, don't go through Four Winns, they are probably Garlalick Parts, and u can find the right parts at a marine store, or order them from West Marine.... May be less of a hassle, just my two cents.
Author:  annapolis [ Fri Jun 14, 2013 5:06 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
We got one from Garelick from west marine. The pole was too long and the holes did not match where the holes are currently drilled. We can make work if we have to but we have several boats and little time
Author:  wkearney99 [ Fri Jun 14, 2013 6:02 pm ]
Post subject:  Re: General part questions and pedestal table mount for 2005
As I recall there are several different diameters of garelick parts for this sort of thing. None of which were conveniently available through west marine. I picked up mine via fleabay.
Page 1 of 1 All times are UTC - 6 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/