erie cruiser wrote:
With all the documented problems that Volvo has had with these drives the muskrat issue is one that I was not prepaired for, thanks for sharing. Good luck
LMAO!
| www.iFourWinns.com https://www.smwebhead.com/phpBB3/ |
|
| remove engine hatch, and section between hatch and Swim Plat https://www.smwebhead.com/phpBB3/viewtopic.php?f=6&t=12584 |
Page 1 of 1 |
| Author: | Snoopyhound [ Thu Jan 23, 2014 9:41 pm ] |
| Post subject: | remove engine hatch, and section between hatch and Swim Plat |
I own a Vista 328 ,(2006) and i have contracted a boat builder to remove the engines, and gen set to facilitate replacement of the transom adapters and outdrives. Need to know how to remove the engine hatch, and the fiber glass section between the hatch and the swim platform, to provide more room for hositing the engines? Sorry, typed year wrong, it is a 2006. |
|
| Author: | kd4pbs [ Fri Jan 24, 2014 3:07 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Your boat builder is going to remove the engines but asked you to figure out how to remove the hatch and some fiberglass? For what it's worth, I'd want to find a different "builder" if that happened to me. |
|
| Author: | Snoopyhound [ Fri Jan 24, 2014 7:25 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
I have pressed the builder/shop to narrow down the labor hours to make the swap , to ensure we don't have a runaway on the labor costs. I was trying to help him for the following reasons: 1-his expertise in rebuilding, and building off shore sport fishers in the 50 to 70 foot range is legendary, so it's not a lack of expertise 2-Hatteras is his specialty, so the Four Winns is new territory , except he built a custom hard top for mine to get rid of the bimini top. He likely has the procedure down pat by now, because he planned on contacting Four Winns engineering. |
|
| Author: | acguy [ Fri Jan 24, 2014 8:50 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Post pics of the hard top. I have had to take mine apart before. I think they changed the design. Is your engine hatched hinged or are there 2 floor panels. I have to remove my rear bench and back. You can gain access to the hardware via the transome locker. |
|
| Author: | Snoopyhound [ Sat Jan 25, 2014 8:46 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Mike, You are right, that's what we have been told by a Four Winns dealer. THanks, will post pics when i figure out how to do it! |
|
| Author: | acguy [ Sat Jan 25, 2014 9:26 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
It's fairly easy to get .it all apart I think I had it all out within an hour. Open up a photbucket account (free) upload your pics there then just copy the image code and paste into your post. I would love to see pics of your custom hard top. What is wrong with your. Transom sheild. Did your 328 come with the dreaded xdp drives? |
|
| Author: | Snoopyhound [ Sat Jan 25, 2014 9:44 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Yes to XDP |
|
| Author: | Snoopyhound [ Sat Jan 25, 2014 9:33 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Mike, ran out of patience with PICs . Send Email address, will send some phhotos |
|
| Author: | erie cruiser [ Sun Jan 26, 2014 11:45 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Snoopy, can you please tell us what issues prompted the replacement of the adapters and drives? Are the shields leaking or are you trying to avoid future problems? We have had no problems with our drives (yet) and would like a "heads-up" as to what you have experienced? Thanks |
|
| Author: | Snoopyhound [ Sun Jan 26, 2014 3:24 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Biggest problem I have had is Muskrats( we have a lot of them) Sit on top of the drives( when the boat is in the water ) while they eat their clams, After which they turn and chew the drive bellows . I have used stainless steel mesh to stop Them, but it is a hassle, so I am swapping the drives for a design that is closed On top , and the lines and wires are protected when trimmed down. Our lake is problematic for Pontoon boats, as well, or any vessel they can climb on and chew rubber, wires, or fuel lines. |
|
| Author: | erie cruiser [ Sun Jan 26, 2014 8:03 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
With all the documented problems that Volvo has had with these drives the muskrat issue is one that I was not prepaired for, thanks for sharing. Good luck |
|
| Author: | TFD2001 [ Sun Jan 26, 2014 9:09 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
erie cruiser wrote: With all the documented problems that Volvo has had with these drives the muskrat issue is one that I was not prepaired for, thanks for sharing. Good luck LMAO!
|
|
| Author: | Winter Sux [ Mon Jan 27, 2014 10:18 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
When I'm enjoying a frosty on my deck during boating season, I discovered that muskrats are allergic to lead.  Tree rats too. 
|
|
| Author: | Snoopyhound [ Mon Jan 27, 2014 11:45 am ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
That's definitely a solution , but would be frowned upon in my Marina. |
|
| Author: | kd4pbs [ Mon Jan 27, 2014 3:00 pm ] |
| Post subject: | Re: remove engine hatch, and section between hatch and Swim |
Sorry - I misunderstood. I understand now that you're going to do that disassembly. Makes sense! Best wishes for the repair! |
|
| Page 1 of 1 | All times are UTC - 6 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|