www.iFourWinns.com

Dedicated to Current and Future Owners
It is currently Thu Oct 31, 2024 6:35 pm

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 30 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Backfire Hydrolock
PostPosted: Sat Nov 29, 2014 4:48 pm 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Went to start the boat yesterday after being anchored for a couple of hours, when it backfired.
The engine then seemed to have almost seized. I stupidly tried a number of times in desperation.
Upon further inspection and removing some plugs, most pots has salt water in them!
How common is it for a backfire to cause a reverse rotation & suck water in to the engine?
I couldn't get it running again and got an emergency tow.
Back home, I managed to get it running again but the starter now sounds horrible:

http://youtu.be/IOrOKKA_GuQ
<Video> Engine was quickly shut down once started as the hose was not attached.

Engine purrs like a kitten & I'm hoping no internal damage was done.
Oil has no milkiness to it.
Any idea what this nasty starter noise might be?

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sat Nov 29, 2014 6:53 pm 
Offline
email admin your custom rank

Joined: Mon Jul 21, 2014 6:52 pm
Posts: 326
Location: Vancouver, WA
Let me start off by saying I am not a pro in the boat mechanics field. However I did find some info that may be of help -
http://www.marinemechanic.com/site/page88.html

Hope it helps.

_________________
2008 Four Winns h180 Bowrider
3.0 Volvo Penta

2013 Dodge Durango HEMI

Image


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sat Nov 29, 2014 7:41 pm 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Just ran the boat on the hose again. Started first time and runs fine.
Dipstick shows no water, but looking inside the rocker covers is showing a milkshake!
Waaaah! :(

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sat Nov 29, 2014 8:07 pm 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
I'd pick up some oil and filters and change it a couple of times. You want the seawater/emulsified water OUT of there as fast as possible. When it backfired, did it seem to diesel (run backwards?) that can definitely suck water up the exhaust. You have a flapper on the exhaust housing, right? Wonder why it backfired?

I still disagree with Volvo's removal of flappers in the Y pipe, for this reason.
Starter, hard to say, but it had to strain to start it against the water, may have worn the Bendix drive. May still work OK though.

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sun Nov 30, 2014 3:05 pm 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
It is hard to say whether it ran backwards at the backfire, or just turned over another half rotation...
Flappers were removed years ago, as per Volvo spec's.
With the starter, how common is it to have damaged the flywheel's teeth gears?
Does the engine need to come out to inspect/ replace the starter and or flywheel?

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sun Nov 30, 2014 4:06 pm 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
I'd put those flappers back, in fact I bet OMC parts would fit. I had to replace mine after my bad overheat in the summer before this past.
The starter you should be able to get it out if you have room. Hopefully that damn fiberglass they like to have all around the rear of the engine is not in your way. I'd have to take the old starter and b!tch slap the designer with it if that were the case, lol...
On my boat I remove half the the rear seat, the engine bulkheads and slide the battery back. Then I can get it out in about 20 min.
Two bolts go up thru the bottom of the housing into the block. They were either 5/8ths or 9/16ths. I had to replace the starter (second one) from that same incident because it was full of salt water. Good thing they don't cost much. It's heavy helps to have strong arms, and a long 1/2 drive ratchet. An easy way is to tie a strong line around it and have someone you trust hold the line up above the engine, so you can get the bolts started, without having to hold up the starter with one hand and start the bolts with the other. If you have no helper, then lay a 2x4 across the gunnels, and tie the starter up around it at the right height and maneuver it in place. Necessity is the mother of invention lol....

I doubt any damage happened to the flywheel. At most you might replace the bendix drive. It actually didn't sound that bad to me.
You could bench test it or take it to an auto electric shop and see what they say.

https://www.dropbox.com/s/97y7b927tdgll ... r.jpg?dl=0

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sun Nov 30, 2014 4:43 pm 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Thanks Lou.
If I re-fitted the flappers, surely there'd be minimal difference given I'd already have 6+ litres of water in the manifolds anyway? :?
I'm trying to get my hands on a compression tester ASAP to see how bad this predicament really is.
If comp' is good, I'll change the oil/ filter and remove the starter for testing.

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Sun Nov 30, 2014 8:29 pm 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
Deaf, get the salt water/oil mix out NOW, its going to corrode bearings, and other stuff, just like a bad head gasket that leaks coolant into the oil. The comp will only be low if you get rust & pitting on the piston rings and cyl walls.
About where the water came from well you could be right. Its possible for it to get sucked in from the riser itself, (versus it coming up the exhaust from the Y pipe). and Merc actually changed the inner shape of the riser to stop this from happening. They made some clear plastic copies of their standard riser and under certain conditions you could see the water get sucked in from the exhaust stream from the riser.

Does your boat sit low in the water in the stern?

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 12:03 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
I plan on changing the oil when I check the compression, in about 2 hours.
Yes, my boat sits low in the stern - as would any 18ft boat with a 350 Chevy stern drive in it! :P

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 4:28 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Compression test looks promising! 8)

Image

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 5:57 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
The oil - Not so much! :cry:

Image

Have flushed the crankcase out with 10L of crappy Castrol GTX 20w50 ($9.95 for 5L!) and the milkiness has gone.
Will attempt to remove the starter tomorrow and have it tested. It sounds like marbles in a glass jar when it cranks. :?

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 6:10 am 
Offline
email admin your custom rank
User avatar

Joined: Thu Feb 27, 2014 4:04 am
Posts: 219
Location: Melbourne Australia
deafwish wrote:
Went to start the boat yesterday after being anchored for a couple of hours, when it backfired.
The engine then seemed to have almost seized. I stupidly tried a number of times in desperation.
Upon further inspection and removing some plugs, most pots has salt water in them!
How common is it for a backfire to cause a reverse rotation & suck water in to the engine?
I couldn't get it running again and got an emergency tow.
Back home, I managed to get it running again but the starter now sounds horrible:

http://youtu.be/IOrOKKA_GuQ
<Video> Engine was quickly shut down once started as the hose was not attached.

Engine purrs like a kitten & I'm hoping no internal damage was done.
Oil has no milkiness to it.
Any idea what this nasty starter noise might be?


Bugger Mate!! Hope there is no damage!

I hydro-locked an Indmar 5.7... might be the same block.. But it was petrol from a stuck injector not salt water. Anyhow pulled the spark plugs, drained the cylinders, new plugs and away it went no harm done. Not sure on your starter motor though..

Fingers crosses mate!!

_________________
Cheers

Mark
Melbourne
Australia

Boats:
Current: 2004 FW 190
2001 Mastercraft X5
1998 Malibu Response
1999 Sea Ray 180
17 ft Scimitar Barefoot (200hp Yamaha)
16ft Scimitar Ski (Yamaha 115)
1988 Ski Nautique ( Called Ski Antique)


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 6:30 am 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
Cheers Mark.
I'm hoping I can get away with this with only a new starter, but after looking at OEM starters, I can almost buy new heads for that money!!! :shock: :cry:

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Mon Dec 01, 2014 9:08 am 
Offline
email admin your custom rank

Joined: Thu Jun 29, 2006 10:26 pm
Posts: 5686
Location: Long Island NY
Here in the US you can get an aftermarket starter (Sierra) for about $170 US, see who distributes Sierra parts in Aust. They are part of Teleflex and one of the biggest after market marine companies in the world . No need for a $$$ OE v/p starter. Simple Chevy starter with marine screen to prevent sparks...
I might also ask Hi-Tek about this....the sucking back water...

Also see if your present starter can be repaired. The starter I am using now started acting up a few years ago. Cause was rusty solenoid due to manifold drain above it leaking. Replaced solenoid for $25, kept it for a spare, had installed a new Sierra. Sierra got trashed 3 years later (cooling hose popped off filled bilge with salt water) . Put old starter back in with new solenoid still works fine.

_________________
88 Four Winns 200 Horizon
4.3 OMC Cobra-4bbl
2002 Walker Bay 10/2012 Suzuki 2.5
2008 Walker Bay 8

1998 Jeep Grand Cherokee 4.0/Selectrac
2007 Jeep Grand Cherokee 5.7 Hemi/Quadradrive II


Top
 Profile  
 
 Post subject: Re: Backfire Hydrolock
PostPosted: Tue Dec 02, 2014 3:09 pm 
Offline
email admin your custom rank

Joined: Fri Jul 27, 2012 11:17 pm
Posts: 1303
Location: Melbourne, Australia
The starter's out & performs flawlessly on the bench - no horrid metallic noises at all.
I've noticed some very minor wear marks on the flywheel's teeth/ gears & was curious as to whether this could cause the noise?
Is it likely that the bushes, brushes or commutator in the starter have gone bad?
Anything else I can try before I potentially waste hundreds on a new starter?

Image

Image

Image

_________________
2011 Four Winns H180 SS.
Aussie built Mustang 2800.
SOLD - 1997 Four Winns Horizon RS


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 30 posts ]  Go to page 1, 2  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 7 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group